A vulnerability in the Cisco IOx application hosting environment of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause the Cisco IOx application hosting environment to stop responding, resulting in a denial of service (DoS) condition. This vulnerability is due to the improper handling of HTTP requests. An attacker could exploit this vulnerability by sending crafted HTTP requests to an affected device. A successful exploit could allow the attacker to cause the Cisco IOx application hosting environment to stop responding. The IOx process will need to be manually restarted to recover services.

A vulnerability in Cisco IOS Software for Cisco Catalyst 2960X, 2960XR, 2960CX, and 3560CX Series Switches could allow an authenticated, local attacker with privilege level 15 or an unauthenticated attacker with physical access to the device to execute persistent code at boot time and break the chain of trust. This vulnerability is due to missing signature verification for specific files that may be loaded during the device boot process. An attacker could exploit this vulnerability by placing a crafted file into a specific location on an affected device. A successful exploit could allow the attacker to execute arbitrary code at boot time. Because this allows the attacker to bypass a major security feature of the device, Cisco has raised the Security Impact Rating (SIR) of this advisory from Medium to High.

A vulnerability in the access control list (ACL) programming of Cisco IOS Software that is running on Cisco Catalyst 1000 Switches and Cisco Catalyst 2960L Switches could allow an unauthenticated, remote attacker to bypass a configured ACL. This vulnerability is due to the use of both an IPv4 ACL and a dynamic ACL of IP Source Guard on the same interface, which is an unsupported configuration. An attacker could exploit this vulnerability by attempting to send traffic through an affected device. A successful exploit could allow the attacker to bypass an ACL on the affected device. Note: Cisco documentation has been updated to reflect that this is an unsupported configuration. However, Cisco is publishing this advisory because the device will not prevent an administrator from configuring both features on the same interface. There are no plans to implement the ability to configure both features on the same interface on Cisco Catalyst 1000 or Catalyst 2960L Switches.

A vulnerability in the web UI feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to conduct a cross-site request forgery (CSRF) attack on an affected system through the web UI. This vulnerability is due to incorrectly accepting configuration changes through the HTTP GET method. An attacker could exploit this vulnerability by persuading a currently authenticated administrator to follow a crafted link. A successful exploit could allow the attacker to change the configuration of the affected device.

A vulnerability in the access control list (ACL) programming of Cisco IOS Software running on Cisco Industrial Ethernet 4000, 4010, and 5000 Series Switches could allow an unauthenticated, remote attacker to bypass a configured ACL. This vulnerability is due to the incorrect handling of IPv4 ACLs on switched virtual interfaces when an administrator enables and disables Resilient Ethernet Protocol (REP). An attacker could exploit this vulnerability by attempting to send traffic through an affected device. A successful exploit could allow the attacker to bypass an ACL on the affected device.

A vulnerability in the web UI feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to conduct a cross-site request forgery (CSRF) attack on an affected system through the web UI.This vulnerability is due to incorrectly accepting

A vulnerability in the access control list (ACL) programming of Cisco IOS Software running on Cisco Industrial Ethernet 4000, 4010, and 5000 Series Switches could allow an unauthenticated, remote attacker to bypass a configured ACL.This vulnerability is due to the incorrect handling

A vulnerability in the implementation of the Simple Network Management Protocol (SNMP) IPv4 access control list (ACL) feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to perform SNMP polling of an affected device, even if it is configured

A vulnerability in the Cisco Group Encrypted Transport VPN (GET VPN) feature of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker who has administrative control of either a group member or a key server to execute arbitrary code on an affected device or cause the device to crash. This vulnerability is due to insufficient validation of attributes in the Group Domain of Interpretation (GDOI) and G-IKEv2 protocols of the GET VPN feature. An attacker could exploit this vulnerability by either compromising an installed key server or modifying the configuration of a group member to point to a key server that is controlled by the attacker. A successful exploit could allow the attacker to execute arbitrary code and gain full control of the affected system or cause the affected system to reload, resulting in a denial of service (DoS) condition. For more information, see the Details ["#details"] section of this advisory.

A vulnerability in the Cisco Group Encrypted Transport VPN (GET VPN) feature of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker who has administrative control of either a group member or a key server to execute arbitrary code on an affected device or

A vulnerability in the IPv6 DHCP (DHCPv6) client module of Cisco Adaptive Security Appliance (ASA) Software, Cisco Firepower Threat Defense (FTD) Software, Cisco IOS Software, and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to insufficient validation of DHCPv6 messages. An attacker could exploit this vulnerability by sending crafted DHCPv6 messages to an affected device. A successful exploit could allow the attacker to cause the device to reload, resulting in a DoS condition. Note: To successfully exploit this vulnerability, the attacker would need to either control the DHCPv6 server or be in a man-in-the-middle position.

A vulnerability in the IPv6 DHCP (DHCPv6) client module of Cisco Adaptive Security Appliance (ASA) Software, Cisco Firepower Threat Defense (FTD) Software, Cisco IOS Software, and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition

Multiple vulnerabilities in the Cisco IOx application hosting environment on multiple Cisco platforms could allow an attacker to inject arbitrary commands into the underlying host operating system, execute arbitrary code on the underlying host operating system, install applications without being authenticated, or conduct a cross-site scripting (XSS) attack against a user of the affected software. For more information about these vulnerabilities, see the Details section of this advisory.

Multiple vulnerabilities that affect Cisco Catalyst Digital Building Series Switches and Cisco Catalyst Micro Switches could allow an attacker to execute persistent code at boot time or to permanently prevent the device from booting, resulting in a permanent denial of service (DoS) condition. For more information about these vulnerabilities, see the Details section of this advisory.

Multiple vulnerabilities that affect Cisco Catalyst Digital Building Series Switches and Cisco Catalyst Micro Switches could allow an attacker to execute persistent code at boot time or to permanently prevent the device from booting, resulting in a permanent denial of service (DoS) condition. For more information about these vulnerabilities, see the Details section of this advisory. Cisco has released software updates that address these vulnerabilities. There are no workarounds that address these vulnerabilities. This advisory is available at the following link:https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-cdb-cmicr-dos-KJjFtNb

A vulnerability in the Voice Telephony Service Provider (VTSP) service of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to bypass configured destination patterns and dial arbitrary numbers. This vulnerability is due to insufficient validation of dial strings at Foreign Exchange Office (FXO) interfaces. An attacker could exploit this vulnerability by sending a malformed dial string to an affected device via either the ISDN protocol or SIP. A successful exploit could allow the attacker to conduct toll fraud, resulting in unexpected financial impact to affected customers.

A vulnerability in the Link Layer Discovery Protocol (LLDP) message parser of Cisco IOS Software and Cisco IOS XE Software could allow an attacker to trigger a reload of an affected device, resulting in a denial of service (DoS) condition. This vulnerability is due to improper initialization of a buffer. An attacker could exploit this vulnerability via any of the following methods: An authenticated, remote attacker could access the LLDP neighbor table via either the CLI or SNMP while the device is in a specific state. An unauthenticated, adjacent attacker could corrupt the LLDP neighbor table by injecting specific LLDP frames into the network and then waiting for an administrator of the device or a network management system (NMS) managing the device to retrieve the LLDP neighbor table of the device via either the CLI or SNMP. An authenticated, adjacent attacker with SNMP read-only credentials or low privileges on the device CLI could corrupt the LLDP neighbor table by injecting specific LLDP frames into the network and then accessing the LLDP neighbor table via either the CLI or SNMP. A successful exploit could allow the attacker to cause the affected device to crash, resulting in a reload of the device.

A vulnerability in Address Resolution Protocol (ARP) management of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to prevent an affected device from resolving ARP entries for legitimate hosts on the connected subnets. This vulnerability exists because ARP entries are mismanaged. An attacker could exploit this vulnerability by continuously sending traffic that results in incomplete ARP entries. A successful exploit could allow the attacker to cause ARP requests on the device to be unsuccessful for legitimate hosts, resulting in a denial of service (DoS) condition.

A vulnerability in the Cisco IOx application hosting environment of multiple Cisco platforms could allow an authenticated, remote attacker to conduct directory traversal attacks and read and write files on the underlying operating system or host system. This vulnerability occurs because the device does not properly validate URIs in IOx API requests. An attacker could exploit this vulnerability by sending a crafted API request that contains directory traversal character sequences to an affected device. A successful exploit could allow the attacker to read or write arbitrary files on the underlying operating system.

A vulnerability in the dragonite debugger of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, local attacker to escalate from privilege level 15 to root privilege. The vulnerability is due to the presence of development testing and verification scripts that remained on the device. An attacker could exploit this vulnerability by bypassing the consent token mechanism with the residual scripts on the affected device. A successful exploit could allow the attacker to escalate from privilege level 15 to root privilege. Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability. This advisory is available at the following link:https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-XE-FSM-Yj8qJbJc

A vulnerability in Address Resolution Protocol (ARP) management of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to prevent an affected device from resolving ARP entries for legitimate hosts on the connected subnets. This vulnerability exists because ARP entries are mismanaged. An attacker could exploit this vulnerability by continuously sending traffic that results in incomplete ARP entries. A successful exploit could allow the attacker to cause ARP requests on the device to be unsuccessful for legitimate hosts, resulting in a denial of service (DoS) condition. Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability. This advisory is available at the following link:https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-arp-mtfhBfjE

A vulnerability in the CLI implementation of a specific command of Cisco IOS XE Software could allow an authenticated, local attacker to overwrite arbitrary files in the underlying host file system. The vulnerability is due to insufficient validation of the parameters of a specific CLI command. An attacker could exploit this vulnerability by issuing that command with specific parameters. A successful exploit could allow the attacker to overwrite the content of any arbitrary file that resides on the underlying host file system.

A vulnerability in the CLI parser of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, local attacker to access files from the flash: filesystem. The vulnerability is due to insufficient application of restrictions during the execution of a specific command. An attacker could exploit this vulnerability by using a specific command at the command line. A successful exploit could allow the attacker to obtain read-only access to files that are located on the flash: filesystem that otherwise might not have been accessible.

A vulnerability in the CLI parser of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, local attacker to access files from the flash: filesystem. The vulnerability is due to insufficient application of restrictions during the execution of a specific command. An attacker could exploit this vulnerability by using a specific command at the command line. A successful exploit could allow the attacker to obtain read-only access to files that are located on the flash: filesystem that otherwise might not have been accessible. Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability. This advisory is available at the following link:https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-info-disclosure-V4BmJBNF

A vulnerability in the 802.1X feature of Cisco Catalyst 2960-L Series Switches and Cisco Catalyst CDB-8P Switches could allow an unauthenticated, adjacent attacker to forward broadcast traffic before being authenticated on the port. The vulnerability exists because broadcast traffic that is received on the 802.1X-enabled port is mishandled. An attacker could exploit this vulnerability by sending broadcast traffic on the port before being authenticated. A successful exploit could allow the attacker to send and receive broadcast traffic on the 802.1X-enabled port before authentication.

A vulnerability in the Tool Command Language (Tcl) interpreter of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, local attacker with privileged EXEC credentials to cause a denial of service (DoS) condition on an affected system. The vulnerability is due to insufficient input validation of data passed to the Tcl interpreter. An attacker could exploit this vulnerability by executing crafted Tcl arguments on an affected device. An exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition.

A vulnerability in the Tool Command Language (Tcl) interpreter of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, local attacker with privileged EXEC credentials to execute arbitrary code on the underlying operating system (OS) with root privileges. The vulnerability is due to insufficient input validation of data passed to the Tcl interpreter. An attacker could exploit this vulnerability by loading malicious Tcl code on an affected device. A successful exploit could allow the attacker to cause memory corruption or execute the code with root privileges on the underlying OS of the affected device.

Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability. This advisory is available at the following link:https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-tcl-ace-C9KuVKmm

A vulnerability in Security Group Tag Exchange Protocol (SXP) in Cisco IOS Software, Cisco IOS XE Software, and Cisco NX-OS Software could allow an unauthenticated, remote attacker to cause the affected device to reload, resulting in a denial of service (DoS) condition. The vulnerability exists because crafted SXP packets are mishandled. An attacker could exploit this vulnerability by sending specifically crafted SXP packets to the affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition.

Cisco has released software updates that address this vulnerability. There are no workarounds that address this vulnerability. This advisory is available at the following link:https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-sxp-68TEVzR

Multiple Cisco products are affected by a vulnerability in the Snort detection engine that could allow an unauthenticated, remote attacker to bypass the configured file policies on an affected system. The vulnerability is due to errors in how the Snort detection engine handles specific HTTP responses. An attacker could exploit this vulnerability by sending crafted HTTP packets that would flow through an affected system. A successful exploit could allow the attacker to bypass the configured file policies and deliver a malicious payload to the protected network.

A vulnerability in the web framework code of Cisco IOS and Cisco IOS XE Software could allow an authenticated, remote attacker to conduct a stored cross-site scripting (XSS) attack against a user of the web interface of the affected software using the banner parameter. The vulnerability is due to insufficient input validation of the banner parameters that are passed to the web server of the affected software. An attacker could exploit this vulnerability by crafting a banner parameter and saving it. The attacker could then convince a user of the web interface to access a malicious link or could intercept a user request for the affected web interface and inject malicious code into the request. A successful exploit could allow the attacker to execute arbitrary script code in the context of the affected web interface or allow the attacker to access sensitive browser-based information.