A Use of Multiple Resources with Duplicate Identifier vulnerability in the IKE daemon (iked) of Juniper Networks Junos OS on MX with SPC3 and SRX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS).

On an MX with SPC3 and SRX devices configured for VPN service, when a large number of VPN negotiations fail a peer index rollover will eventually occur. As a result, new peers are assigned index values that are already in use and the iked process starts to crash repeatedly. This results in failure to establish new VPN connections and rekeying existing ones. To restore service the system must be rebooted. Please note that the index value can't be monitored, so customers should monitor tunnel up and down events and if a lot of events occur over an extended period of time it becomes likely that this issue occurs.

To be exposed to this issue the system needs to run iked (vs. kmd which is not affected), which can be verified with:

user@host> show system processes extensive | match "KMD|IKED" This issue affects Junos OS on MX with SPC3, SRX Series:

all versions before 23.2R2-S7, 23.4 versions before 23.4R2-S6, 24.2 versions before 24.2R2-S3, 24.4 versions before 24.4R2-S4, 25.2 versions before 25.2R1-S1.

An Out-of-bounds Write vulnerability in the http-gatekeeper (http-gk) of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause a Denial-of-Service (DoS).

If an SRX Series device is configured for remote-access VPN with pre-logon compliance check, a network-based attacker sending specifically formatted requests can trigger an out of bounds write leading to an http-gk process crash. This crash leads to unavailability of all services depending on the [ system services web-management ] configuration (like J-Web, remote access VPN and firewall authentication) until the process automatically restarts.

This issue affects Junos OS on SRX Series:

23.2 versions before 23.2R2-S7, 23.4 versions before 23.4R2-S8, 24.2 versions before 24.2R2-S4, 24.4 versions before 24.4R2-S4, 25.2 versions before 25.2R2, 25.4 versions before 25.4R1-S1, 25.4R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the chassis control daemon (chassisd) of Juniper Networks Junos OS on SRX1500, SRX4100, SRX4200 and SRX4600 allows a local attacker with low privileges to cause a complete Denial of Service (DoS).

When a specific 'show chassis' CLI command is executed, chassisd crashes and restarts which causes a momentary impact to all traffic until all modules are online again.

This issue affects Junos OS on SRX1500, SRX4100, SRX4200 and SRX4600:

23.2 versions before 23.2R2-S6, 23.4 versions before 23.4R2-S7 24.2 versions before 24.2R2-S2, 24.4 versions before 24.4R2, 25.2 versions before 25.2R1-S1, 25.2R2.

A NULL Pointer Dereference vulnerability in the chassis daemon (chassisd) of Juniper Networks Junos OS on MX, SRX and EX Series allows a local attacker with low privileges to cause a Denial-of-Service (DoS).

When a user executes the 'show chassis' command with specifically crafted options, chassisd will crash and restart. Due to this all components but the Routing Engine (RE) in the chassis are reinitialized, which leads to a complete service outage, which the system automatically recovers from.

This issue affects:

Junos OS on MX, SRX and EX Series, except MX10000 Series and MX304:

all versions before 22.4R3-S8, 23.2 versions before 23.2R2-S5, 23.4 versions before 23.4R2-S6, 24.2 versions before 24.2R2-S2, 24.4 versions before 24.4R2.

An Incorrect Authorization vulnerability in the web server of Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to reach the

Juniper Web Device Manager

(J-Web).

When Juniper Secure connect (JSC) is enabled on specific interfaces, or multiple interfaces are configured for J-Web, the J-Web UI is reachable over more than the intended interfaces. This issue affects Junos OS:

all versions before 21.4R3-S9, 22.2 versions before 22.2R3-S5, 22.4 versions before 22.4R3-S5, 23.2 versions before 23.2R2-S3, 23.4 versions before 23.4R2-S5, 24.2 versions before 24.2R2.

An Exposure of Sensitive Information to an Unauthorized Actor vulnerability in the command-line interface (CLI) of Juniper Networks Junos OS on SRX Series devices allows a local, low-privileged user with access to the Junos CLI to view the contents of sensitive files on the file system.

Through the execution of either 'show services advanced-anti-malware' or 'show services security-intelligence' command, a user with limited permissions (e.g., a low privilege login class user) can access protected files that should not be accessible to the user. These files may contain sensitive information that can be used to cause further impact to the system.

This issue affects Junos OS SRX Series:

All versions before 21.4R3-S8,

from 22.2 before 22.2R3-S5,

from 22.3 before 22.3R3-S3, from 22.4 before 22.4R3-S2,

from 23.2 before 23.2R2-S1,

from 23.4 before 23.4R2.

An Exposure of Sensitive Information to an Unauthorized Actor vulnerability in the command-line interface (CLI) of Juniper Networks Junos OS on SRX Series devices allows a local, low-privileged user with access to the Junos CLI to view the contents of protected files on the file system.

Through the execution of crafted CLI commands, a user with limited permissions (e.g., a low privilege login class user) can access protected files that should not be accessible to the user. These files may contain sensitive information that can be used to cause further impact to the system.

This issue affects Junos OS on SRX Series:

All versions before 21.4R3-S8,  22.2 before 22.2R3-S5,  22.3 before 22.3R3-S4,  22.4 before 22.4R3-S4,  23.2 before 23.2R2-S2,  23.4 before 23.4R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the flow daemon (flowd) of Juniper Networks Junos OS on

SRX4600 and SRX5000 Series

allows an attacker to send TCP packets with

SYN/FIN or SYN/RST

flags, bypassing the expected blocking of these packets.

A TCP packet with SYN/FIN or SYN/RST should be dropped in flowd. However, when no-syn-check and Express Path are enabled, these TCP packets are unexpectedly transferred to the downstream network.

This issue affects Junos OS on SRX4600 and SRX5000 Series:

All versions before 21.2R3-S8, from 21.4 before 21.4R3-S7, from 22.1 before 22.1R3-S6, from 22.2 before 22.2R3-S4, from 22.3 before 22.3R3-S3, from 22.4 before 22.4R3-S2, from 23.2 before 23.2R2, from 23.4 before 23.4R1-S1, 23.4R2.

A Missing Authentication for Critical Function vulnerability in the Packet Forwarding Engine (pfe) of Juniper Networks Junos OS on MX Series with SPC3, and SRX Series allows an unauthenticated network-based attacker to cause limited impact to the integrity or availability of the device.

If a device is configured with IPsec authentication algorithm hmac-sha-384 or hmac-sha-512, tunnels are established normally but for traffic traversing the tunnel no authentication information is sent with the encrypted data on egress, and no authentication information is expected on ingress. So if the peer is an unaffected device transit traffic is going to fail in both directions. If the peer is an also affected device transit traffic works, but without authentication, and configuration and CLI operational commands indicate authentication is performed. This issue affects Junos OS:

All versions before 20.4R3-S7, 21.1 versions before 21.1R3,  21.2 versions before 21.2R2-S1, 21.2R3,  21.3 versions before 21.3R1-S2, 21.3R2.

A Missing Authentication for Critical Function vulnerability in Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause limited impact to the file system integrity.

With a specific request to

webauthoperation.php

that doesn't require authentication, an attacker is able to upload and download arbitrary files via J-Web, leading to a loss of

integrity or confidentiality, which may allow chaining to other vulnerabilities.

This issue affects Juniper Networks Junos OS on SRX Series:

21.2 versions prior to 21.2R3-S8; 21.4

versions prior to

21.4R3-S6; 22.1

versions prior to

22.1R3-S5; 22.2

versions prior to

22.2R3-S3; 22.3

versions prior to

22.3R3-S2; 22.4 versions prior to 22,4R2-S2, 22.4R3; 23.2 versions prior to

23.2R1-S2, 23.2R2.

A Missing Authentication for Critical Function vulnerability in Juniper Networks Junos OS on SRX Series allows an unauthenticated, network-based attacker to cause limited impact to the file system integrity.

With a specific request to user.php that doesn't require authentication an attacker is able to upload arbitrary files via J-Web, leading to a loss of

integrity

for a certain

part of the file system, which may allow chaining to other vulnerabilities.

This issue affects Juniper Networks Junos OS on SRX Series:

All versions prior to 20.4R3-S8; 21.1 versions 21.1R1 and later; 21.2 versions prior to 21.2R3-S6; 21.3 versions

prior to

21.3R3-S5; 21.4 versions

prior to

21.4R3-S5; 22.1 versions

prior to

22.1R3-S3; 22.2 versions

prior to

22.2R3-S2; 22.3 versions

prior to

22.3R2-S2, 22.3R3; 22.4 versions

prior to

22.4R2-S1, 22.4R3.

A PHP External Variable Modification vulnerability in J-Web of Juniper Networks Junos OS on EX Series allows an unauthenticated, network-based attacker to control certain, important environment variables.

Using a crafted request an attacker is able to modify

certain PHP environment variables leading to partial loss of integrity, which may allow chaining to other vulnerabilities. This issue affects Juniper Networks Junos OS on EX Series:

All versions prior to 20.4R3-S9; 21.1 versions 21.1R1 and later; 21.2 versions prior to 21.2R3-S7; 21.3 versions

prior to

21.3R3-S5; 21.4 versions

prior to

21.4R3-S5; 22.1 versions

prior to

22.1R3-S4; 22.2 versions

prior to

22.2R3-S2; 22.3 versions

prior to 22.3R3-S1; 22.4 versions

prior to

22.4R2-S2, 22.4R3; 23.2 versions prior to

23.2R1-S1, 23.2R2.

A Missing Authentication for Critical Function vulnerability in Juniper Networks Junos OS on EX Series allows an unauthenticated, network-based attacker to cause limited impact to the file system integrity.

With a specific request to installAppPackage.php that doesn't require authentication an attacker is able to upload arbitrary files via J-Web, leading to a loss of

integrity

for a certain

part of the file system, which may allow chaining to other vulnerabilities.

This issue affects Juniper Networks Junos OS on EX Series:

All versions prior to 20.4R3-S8; 21.1 versions 21.1R1 and later; 21.2 versions prior to 21.2R3-S6; 21.3 versions

prior to

21.3R3-S5; 21.4 versions

prior to

21.4R3-S4; 22.1 versions

prior to

22.1R3-S3; 22.2 versions

prior to

22.2R3-S1; 22.3 versions

prior to

22.3R2-S2, 22.3R3; 22.4 versions

prior to

22.4R2-S1, 22.4R3.

An Incomplete Internal State Distinction vulnerability in the packet forwarding engine (PFE) of Juniper Networks Junos OS on SRX 4600 and SRX 5000 Series allows an adjacent attacker to cause a Denial of Service (DoS).

If an SRX is configured in L2 transparent mode the receipt of a specific genuine packet can cause a single Packet Processing Engines (PPE) component of the PFE to run into a loop, which in turn will render the PPE unavailable. Each packet will cause one PPE to get into a loop, leading to a gradual performance degradation until all PPEs are unavailable and all traffic processing stops. To recover the affected FPC need to be restarted.

This issue affects Juniper Networks Junos OS on SRX 4600 and SRX 5000 Series: 20.1 version 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S7; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3-S7; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S1; 22.1 versions prior to 22.1R3; 22.2 versions prior to 22.2R2; 22.3 versions prior to 22.3R1-S1, 22.3R2.

An Out-of-bounds Read vulnerability in the flow processing daemon (flowd) of Juniper Networks Junos OS on SRX Series allows a local, authenticated attacker with low privileges, to cause a Denial of Service (DoS).

If a low privileged user executes a specific CLI command, flowd which is responsible for traffic forwarding in SRX crashes and generates a core dump. This will cause temporary traffic interruption until the flowd process is restarted automatically. Continued execution of this command will lead to a sustained DoS.

This issue affects Juniper Networks Junos OS on SRX Series: All versions prior to 20.2R3-S7; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3-S4; 21.4 versions prior to 21.4R3-S3; 22.1 versions prior to 22.1R3-S1; 22.2 versions prior to 22.2R3; 22.3 versions prior to 22.3R2; 22.4 versions prior to 22.4R1-S1, 22.4R2.

An Improperly Controlled Sequential Memory Allocation vulnerability in the Juniper Networks Deep Packet Inspection-Decoder (JDPI-Decoder) Application Signature component of Junos OS's AppID service on SRX Series devices will stop the JDPI-Decoder from identifying dynamic application traffic, allowing an unauthenticated network-based attacker to send traffic to the target device using the JDPI-Decoder, designed to inspect dynamic application traffic and take action upon this traffic, to instead begin to not take action and to pass the traffic through. An example session can be seen by running the following command and evaluating the output. user@device# run show security flow session source-prefix <address/mask> extensive Session ID: <session ID>, Status: Normal, State: Active Policy name: <name of policy> Dynamic application: junos:UNKNOWN, <<<<< LOOK HERE Please note, the JDPI-Decoder and the AppID SigPack are both affected and both must be upgraded along with the operating system to address the matter. By default, none of this is auto-enabled for automatic updates. This issue affects: Juniper Networks any version of the JDPI-Decoder Engine prior to version 5.7.0-47 with the JDPI-Decoder enabled using any version of the AppID SigPack prior to version 1.550.2-31 (SigPack 3533) on Junos OS on SRX Series: All versions prior to 19.1R3-S10; 19.2 versions prior to 19.2R3-S7; 19.3 versions prior to 19.3R3-S8; 19.4 versions prior to 19.4R3-S11; 20.1 version 20.1R1 and later versions prior to 20.2R3-S7; 20.3 version 20.3R1 and later versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S3; 22.1 versions prior to 22.1R3-S1; 22.2 versions prior to 22.2R2-S1, 22.2R3; 22.3 versions prior to 22.3R1-S2, 22.3R2;

An Out-of-bounds Write vulnerability in the Internet Key Exchange Protocol daemon (iked) of Juniper Networks Junos OS on SRX series and MX with SPC3 allows an authenticated, network-based attacker to cause a Denial of Service (DoS). iked will crash and restart, and the tunnel will not come up when a peer sends a specifically formatted payload during the negotiation. This will impact other IKE negotiations happening at the same time. Continued receipt of this specifically formatted payload will lead to continuous crashing of iked and thereby the inability for any IKE negotiations to take place. Note that this payload is only processed after the authentication has successfully completed. So the issue can only be exploited by an attacker who can successfully authenticate. This issue affects Juniper Networks Junos OS on SRX Series, and MX Series with SPC3: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2.

An Unchecked Input for Loop Condition vulnerability in a NAT library of Juniper Networks Junos OS allows a local authenticated attacker with low privileges to cause a Denial of Service (DoS). When an inconsistent "deterministic NAT" configuration is present on an SRX, or MX with SPC3 and then a specific CLI command is issued the SPC will crash and restart. Repeated execution of this command will lead to a sustained DoS. Such a configuration is characterized by the total number of port blocks being greater than the total number of hosts. An example for such configuration is: [ services nat source pool TEST-POOL address x.x.x.0/32 to x.x.x.15/32 ] [ services nat source pool TEST-POOL port deterministic block-size 1008 ] [ services nat source pool TEST-POOL port deterministic host address y.y.y.0/24] [ services nat source pool TEST-POOL port deterministic include-boundary-addresses] where according to the following calculation: 65536-1024=64512 (number of usable ports per IP address, implicit) 64512/1008=64 (number of port blocks per Nat IP) x.x.x.0/32 to x.x.x.15/32 = 16 (NAT IP addresses available in NAT pool) total port blocks in NAT Pool = 64 blocks per IP 16 IPs = 1024 Port blocks host address y.y.y.0/24 = 256 hosts (with include-boundary-addresses) If the port block size is configured to be 4032, then the total port blocks are (64512/4032) 16 = 256 which is equivalent to the total host addresses of 256, and the issue will not be seen. This issue affects Juniper Networks Junos OS on SRX Series, and MX Series with SPC3: All versions prior to 19.4R3-S10; 20.1 version 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S1; 22.1 versions prior to 22.1R2-S2, 22.1R3; 22.2 versions prior to 22.2R2.

An Improper Release of Memory Before Removing Last Reference vulnerability in the Session Initiation Protocol (SIP) Application Layer Gateway (ALG) of Juniper Networks Junos OS allows unauthenticated network-based attacker to cause a partial Denial of Service (DoS). On all MX and SRX platforms, if the SIP ALG is enabled, receipt of a specific SIP packet will create a stale SIP entry. Sustained receipt of such packets will cause the SIP call table to eventually fill up and cause a DoS for all SIP traffic. The SIP call usage can be monitored by "show security alg sip calls". To be affected the SIP ALG needs to be enabled, either implicitly / by default or by way of configuration. Please verify on SRX with: user@host> show security alg status | match sip SIP : Enabled Please verify on MX whether the following is configured: [ services ... rule <rule-name> (term <term-name>) from/match application/application-set <name> ] where either a. name = junos-sip or an application or application-set refers to SIP: b. [ applications application <name> application-protocol sip ] or c. [ applications application-set <name> application junos-sip ] This issue affects Juniper Networks Junos OS on SRX Series and MX Series: 20.4 versions prior to 20.4R3-S2; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R2-S2; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2; 21.4 versions prior to 21.4R2. This issue does not affect Juniper Networks Junos OS versions prior to 20.4R1. Juniper SIRT is not aware of any malicious exploitation of this vulnerability.

A cache poisoning vulnerability was found in BIND when using forwarders. Bogus NS records supplied by the forwarders may be cached and used by name if it needs to recurse for any reason. This issue causes it to obtain and pass on potentially incorrect answers. This flaw allows a remote high privileged attacker to manipulate cache results with incorrect records, leading to queries made to the wrong servers, possibly resulting in false information received on the client's end.

Improper Handling of Exceptional Conditions in Ethernet interface frame processing of Juniper Networks Junos OS allows an attacker to send specially crafted frames over the local Ethernet segment, causing the interface to go into a down state, resulting in a Denial of Service (DoS) condition. The interface does not recover on its own and the FPC must be reset manually. Continued receipt and processing of these frames will create a sustained Denial of Service (DoS) condition. This issue is platform-specific and affects the following platforms and line cards: MPC7E/8E/9E and MPC10E on MX240, MX480, MX960, MX2008, MX2010, and MX2020 MX204, MX10003, MX10008, MX10016 EX9200, EX9251 SRX4600 No other products or platforms are affected by this vulnerability. An indication of this issue occurring can be seen in the system log messages, as shown below: user@host> show log messages | match "Failed to complete DFE tuning" fpc4 smicphydfetuningstate: et-4/1/6 - Failed to complete DFE tuning (count 3) and interface will be in a permanently down state: user@host> show interfaces et-4/1/6 terse Interface Admin Link Proto Local Remote et-4/1/6 up down et-4/1/6.0 up down aenet --> ae101.0 This issue affects Juniper Networks Junos OS: 16.1 versions prior to 16.1R7-S7 on MX Series; 17.1R1 and later versions prior to 17.2R3-S3 on MX Series; 17.3 versions prior to 17.3R3-S8 on MX Series; 17.4 versions prior to 17.4R2-S11, 17.4R3-S1 on MX Series, SRX4600; 18.1 versions prior to 18.1R3-S10 on MX Series, EX9200 Series, SRX4600; 18.2 versions prior to 18.2R3-S3 on MX Series, EX9200 Series, SRX4600; 18.3 versions prior to 18.3R3-S1 on MX Series, EX9200 Series, SRX4600; 18.4 versions prior to 18.4R2-S3, 18.4R3 on MX Series, EX9200 Series, SRX4600; 19.1 versions prior to 19.1R2-S1, 19.1R3 on MX Series, EX9200 Series, SRX4600; 19.2 versions prior to 19.2R1-S3, 19.2R2 on MX Series, EX9200 Series, SRX4600; 19.3 versions prior to 19.3R2 on MX Series, EX9200 Series, SRX4600. This issue does not affect Juniper Networks Junos OS versions prior to 16.1R1.

When user-defined ARP Policer is configured and applied on one or more Aggregated Ethernet (AE) interface units, a Time-of-check Time-of-use (TOCTOU) Race Condition vulnerability between the Device Control Daemon (DCD) and firewall process (dfwd) daemons of Juniper Networks Junos OS allows an attacker to bypass the user-defined ARP Policer. In this particular case the User ARP policer is replaced with default ARP policer. To review the desired ARP Policers and actual state one can run the command "show interfaces <> extensive" and review the output. See further details below. An example output is: show interfaces extensive | match policer Policer: Input: defaultarppolicer <<< incorrect if user ARP Policer was applied on an AE interface and the default ARP Policer is displayed Policer: Input: jtac-arp-ae5.317-inet-arp <<< correct if user ARP Policer was applied on an AE interface For all platforms, except SRX Series: This issue affects Juniper Networks Junos OS: All versions 5.6R1 and all later versions prior to 18.4 versions prior to 18.4R2-S9, 18.4R3-S9 with the exception of 15.1 versions 15.1R7-S10 and later versions; 19.4 versions prior to 19.4R3-S3; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2; This issue does not affect Juniper Networks Junos OS versions prior to 5.6R1. On SRX Series this issue affects Juniper Networks Junos OS: 18.4 versions prior to 18.4R2-S9, 18.4R3-S9; 19.4 versions prior to 19.4R3-S4; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S2; 20.3 version 20.3R1 and later versions; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. This issue does not affect 18.4 versions prior to 18.4R1 on SRX Series. This issue does not affect Junos OS Evolved.

A path traversal vulnerability in the Juniper Networks SRX and vSRX Series may allow an authenticated J-web user to read sensitive system files. This issue affects Juniper Networks Junos OS on SRX and vSRX Series: 19.3 versions prior to 19.3R2-S6, 19.3R3-S1; 19.4 versions prior to 19.4R2-S4, 19.4R3; 20.1 versions prior to 20.1R1-S4, 20.1R2; 20.2 versions prior to 20.2R1-S3, 20.2R2; This issue does not affect Juniper Networks Junos OS versions prior to 19.3R1.

On Juniper Networks SRX Series and NFX Series, a local authenticated user with access to the shell may obtain the Web API service private key that is used to provide encrypted communication between the Juniper device and the authenticator services. Exploitation of this vulnerability may allow an attacker to decrypt the communications between the Juniper device and the authenticator service. This Web API service is used for authentication services such as the Juniper Identity Management Service, used to obtain user identity for Integrated User Firewall feature, or the integrated ClearPass authentication and enforcement feature. This issue affects Juniper Networks Junos OS on Networks SRX Series and NFX Series: 12.3X48 versions prior to 12.3X48-D105; 15.1X49 versions prior to 15.1X49-D190; 16.1 versions prior to 16.1R7-S8; 17.2 versions prior to 17.2R3-S4; 17.3 versions prior to 17.3R3-S8; 17.4 versions prior to 17.4R2-S11, 17.4R3; 18.1 versions prior to 18.1R3-S7; 18.2 versions prior to 18.2R3; 18.3 versions prior to 18.3R2-S4, 18.3R3; 18.4 versions prior to 18.4R1-S7, 18.4R2; 19.1 versions prior to 19.1R2; 19.2 versions prior to 19.2R1-S4, 19.2R2.

On Juniper Networks Junos OS devices configured as a DHCP forwarder, the Juniper Networks Dynamic Host Configuration Protocol Daemon (jdhcp) process might crash when receiving a malformed DHCP packet. This issue only affects devices configured as DHCP forwarder with forward-only option, that forward specified DHCP client packets, without creating a new subscriber session. The jdhcpd daemon automatically restarts without intervention, but continuous receipt of the malformed DHCP packet will repeatedly crash jdhcpd, leading to an extended Denial of Service (DoS) condition. This issue can be triggered only by DHCPv4, it cannot be triggered by DHCPv6. This issue affects Juniper Networks Junos OS: 12.3 versions prior to 12.3R12-S16; 12.3X48 versions prior to 12.3X48-D105 on SRX Series; 14.1X53 versions prior to 14.1X53-D60 on EX and QFX Series; 15.1 versions prior to 15.1R7-S7; 15.1X49 versions prior to 15.1X49-D221, 15.1X49-D230 on SRX Series; 15.1X53 versions prior to 15.1X53-D593 on EX2300/EX3400; 16.1 versions prior to 16.1R7-S5.

Background For regular, unencrypted FTP traffic, the FTP ALG can inspect the unencrypted control channel and open related sessions for the FTP data channel. These related sessions (gates) are specific to source and destination IPs and ports of client and server. The design intent of the ftps-extensions option (which is disabled by default) is to provide similar functionality when the SRX secures the FTP/FTPS client. As the control channel is encrypted, the FTP ALG cannot inspect the port specific information and will open a wider TCP data channel (gate) from client IP to server IP on all destination TCP ports. In FTP/FTPS client environments to an enterprise network or the Internet, this is the desired behavior as it allows firewall policy to be written to FTP/FTPS servers on well-known control ports without using a policy with destination IP ANY and destination port ANY. Issue The ftps-extensions option is not intended or recommended where the SRX secures the FTPS server, as the wide data channel session (gate) will allow the FTPS client temporary access to all TCP ports on the FTPS server. The data session is associated to the control channel and will be closed when the control channel session closes. Depending on the configuration of the FTPS server, supporting load-balancer, and SRX inactivity-timeout values, the server/load-balancer and SRX may keep the control channel open for an extended period of time, allowing an FTPS client access for an equal duration.​ Note that the ftps-extensions option is not enabled by default.

named in ISC BIND 9.x before 9.9.8-P4 and 9.10.x before 9.10.3-P4 does not properly handle DNAME records when parsing fetch reply messages, which allows remote attackers to cause a denial of service (assertion failure and daemon exit) via a malformed packet to the rndc (aka control channel) interface, related to alist.c and sexpr.c.

Embedthis Appweb before 4.6.6 and 5.x before 5.2.1 allows remote attackers to cause a denial of service (NULL pointer dereference) via a Range header with an empty value, as demonstrated by "Range: x=,".