An Improper Input Validation vulnerability in the VxLAN packet forwarding engine (PFE) of Juniper Networks Junos OS on QFX5000 Series, EX4600 Series devices allows an unauthenticated, adjacent attacker, sending two or more genuine packets in the same VxLAN topology to possibly cause a DMA memory leak to occur under various specific operational conditions. The scenario described here is the worst-case scenario. There are other scenarios that require operator action to occur.

An indicator of compromise may be seen when multiple devices indicate that FPC0 has gone missing when issuing a show chassis fpc command for about 10 to 20 minutes, and a number of interfaces have also gone missing.

Use the following command to determine if FPC0 has gone missing from the device.

show chassis fpc detail This issue affects:

Juniper Networks Junos OS on QFX5000 Series, EX4600 Series:

18.4 version 18.4R2 and later versions prior to 20.4R3-S8; 21.1 version 21.1R1 and later versions prior to 21.2R3-S6; 21.3 versions prior to 21.3R3-S5; 21.4 versions prior to 21.4R3-S4; 22.1 versions prior to 22.1R3-S3; 22.2 versions prior to 22.2R3-S1; 22.3 versions prior to 22.3R2-S2, 22.3R3; 22.4 versions prior to 22.4R2.

An Improperly Controlled Sequential Memory Allocation vulnerability in the Juniper Networks Deep Packet Inspection-Decoder (JDPI-Decoder) Application Signature component of Junos OS's AppID service on SRX Series devices will stop the JDPI-Decoder from identifying dynamic application traffic, allowing an unauthenticated network-based attacker to send traffic to the target device using the JDPI-Decoder, designed to inspect dynamic application traffic and take action upon this traffic, to instead begin to not take action and to pass the traffic through. An example session can be seen by running the following command and evaluating the output. user@device# run show security flow session source-prefix <address/mask> extensive Session ID: <session ID>, Status: Normal, State: Active Policy name: <name of policy> Dynamic application: junos:UNKNOWN, <<<<< LOOK HERE Please note, the JDPI-Decoder and the AppID SigPack are both affected and both must be upgraded along with the operating system to address the matter. By default, none of this is auto-enabled for automatic updates. This issue affects: Juniper Networks any version of the JDPI-Decoder Engine prior to version 5.7.0-47 with the JDPI-Decoder enabled using any version of the AppID SigPack prior to version 1.550.2-31 (SigPack 3533) on Junos OS on SRX Series: All versions prior to 19.1R3-S10; 19.2 versions prior to 19.2R3-S7; 19.3 versions prior to 19.3R3-S8; 19.4 versions prior to 19.4R3-S11; 20.1 version 20.1R1 and later versions prior to 20.2R3-S7; 20.3 version 20.3R1 and later versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S3; 22.1 versions prior to 22.1R3-S1; 22.2 versions prior to 22.2R2-S1, 22.2R3; 22.3 versions prior to 22.3R1-S2, 22.3R2;

An Improper Check for Unusual or Exceptional Conditions vulnerability in the kernel of Juniper Networks Junos OS allows an adjacent unauthenticated attacker to bypass an integrity check. In a 6PE scenario and if an additional integrity check is configured, it will fail to drop specific malformed IPv6 packets, and then these packets will be forwarded to other connected networks. This issue affects Juniper Networks Junos OS: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S7; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R2; 22.2 versions prior to 22.2R2.

An Improper Handling of Length Parameter Inconsistency vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a network based, unauthenticated attacker to cause an RPD crash leading to a Denial of Service (DoS). Continued receipt and processing of this packet will create a sustained Denial of Service (DoS) condition. Upon receipt of a malformed BGP flowspec update, RPD will crash resulting in a Denial of Service. This issue affects Juniper Networks Junos OS: All versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2; 20.3 versions prior to 20.3R1-S1, 20.3R2; Juniper Networks Junos OS Evolved: All versions prior to 20.1R3-EVO; 20.2 versions prior to 20.2R2-EVO; 20.3 versions prior to 20.3R2-EVO;

An Improper Link Resolution Before File Access vulnerability in console port access of Juniper Networks Junos OS on NFX Series allows an attacker to bypass console access controls. When "set system ports console insecure" is enabled, root login is disallowed for Junos OS as expected. However, the root password can be changed using "set system root-authentication plain-text-password" on NFX Series systems, leading to a possible administrative bypass with physical access to the console. Password recovery, changing the root password from a console, should not have been allowed from an insecure console. This is similar to the vulnerability described in CVE-2019-0035 but affects different platforms and in turn requires a different fix. This issue affects Juniper Networks Junos OS on NFX Series: 19.2 versions prior to 19.2R3-S7; 19.3 versions prior to 19.3R3-S8; 19.4 versions prior to 19.4R3-S12; 20.2 versions prior to 20.2R3-S8; 20.4 versions prior to 20.4R3-S7; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S2; 22.1 versions prior to 22.1R3-S1; 22.2 versions prior to 22.2R2-S1, 22.2R3; 22.3 versions prior to 22.3R1-S2, 22.3R2.

An Improper Check or Handling of Exceptional Conditions within the storm control feature of Juniper Networks Junos OS allows an attacker sending a high rate of traffic to cause a Denial of Service. Continued receipt and processing of these packets will create a sustained Denial of Service (DoS) condition. Storm control monitors the level of applicable incoming traffic and compares it with the level specified. If the combined level of the applicable traffic exceeds the specified level, the switch drops packets for the controlled traffic types. This issue affects Juniper Networks Junos OS on QFX10002: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S11; 20.2 versions prior to 20.2R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the packet forwarding engine (pfe) of Juniper Networks Junos OS on MX Series allows an unauthenticated, network-based attacker to cause a Denial of Service (DoS). If specific traffic is received on MX Series and its rate exceeds the respective DDoS protection limit the ingress PFE will crash and restart. Continued receipt of this traffic will create a sustained DoS condition. This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 19.1R3-S10; 19.2 versions prior to 19.2R3-S7; 19.3 versions prior to 19.3R3-S8; 19.4 versions prior to 19.4R3-S11; 20.2 versions prior to 20.2R3-S5; 20.4 versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2.

An Out-of-Bounds Write vulnerability in Flow Processing Daemon (flowd) of Juniper Networks Junos OS allows an unauthenticated, network-based attacker to cause Denial of Service (DoS). On SRX Series devices using Unified Policies with IPv6, when a specific IPv6 packet goes through a dynamic-application filter which will generate an ICMP deny message, the flowd core is observed and the PFE is restarted. This issue affects: Juniper Networks Junos OS on SRX Series: 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S3; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2; 21.4 versions prior to 21.4R2.

An Out-of-bounds Write vulnerability in the Internet Key Exchange Protocol daemon (iked) of Juniper Networks Junos OS on SRX series and MX with SPC3 allows an authenticated, network-based attacker to cause a Denial of Service (DoS). iked will crash and restart, and the tunnel will not come up when a peer sends a specifically formatted payload during the negotiation. This will impact other IKE negotiations happening at the same time. Continued receipt of this specifically formatted payload will lead to continuous crashing of iked and thereby the inability for any IKE negotiations to take place. Note that this payload is only processed after the authentication has successfully completed. So the issue can only be exploited by an attacker who can successfully authenticate. This issue affects Juniper Networks Junos OS on SRX Series, and MX Series with SPC3: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2.

An Improper Handling of Unexpected Data Type vulnerability in the handling of SIP calls in Juniper Networks Junos OS on SRX Series and MX Series platforms allows an attacker to cause a memory leak leading to Denial of Services (DoS). This issue occurs on all MX Series platforms with MS-MPC or MS-MIC card and all SRX Series platforms where SIP ALG is enabled. Successful exploitation of this vulnerability prevents additional SIP calls and applications from succeeding. The SIP ALG needs to be enabled, either implicitly / by default or by way of configuration. To confirm whether SIP ALG is enabled on SRX use the following command: user@host> show security alg status | match sip SIP : Enabled This issue affects Juniper Networks Junos OS on SRX Series and on MX Series: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S8, 19.4R3-S10; 20.1 versions 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S5; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2-S2, 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2, 22.1R3-S1. This issue does not affect Juniper Networks Junos OS on SRX Series and on MX Series: All versions prior to 18.2R1.

A Missing Release of Memory after Effective Lifetime vulnerability in the Flow Processing Daemon (flowd) of Juniper Networks Junos OS allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS). In an IPsec VPN environment, a memory leak will be seen if a DH or ECDH group is configured. Eventually the flowd process will crash and restart. This issue affects Juniper Networks Junos OS on SRX Series: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S8, 19.4R3-S10; 20.2 versions prior to 20.2R3-S6; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2.

An Incomplete Cleanup vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent, unauthenticated attacker to cause a Denial of Service (DoS). An rpd crash can occur when an MPLS TE tunnel configuration change occurs on a directly connected router. This issue affects: Juniper Networks Junos OS All versions prior to 18.4R2-S7; 19.1 versions prior to 19.1R3-S2; 19.2 versions prior to 19.2R3; 19.3 versions prior to 19.3R3; 19.4 versions prior to 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2. Juniper Networks Junos OS Evolved All versions prior to 19.2R3-EVO; 19.3 versions prior to 19.3R3-EVO; 19.4 versions prior to 19.4R3-EVO; 20.1 versions prior to 20.1R3-EVO; 20.2 versions prior to 20.2R2-EVO.

An Access of Uninitialized Pointer vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a locally authenticated attacker with low privileges to cause a Denial of Service (DoS). When an MPLS ping is performed on BGP LSPs, the RPD might crash. Repeated execution of this operation will lead to a sustained DoS. This issue affects: Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S12; 19.1 versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R1-S9, 19.2R3-S5; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R2-S7, 19.4R3-S8; 20.1 versions prior to 20.1R3-S4; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R1-S1, 21.1R2; Juniper Networks Junos OS Evolved: All versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R2-EVO.

A Missing Release of Memory after Effective Lifetime vulnerability in the kernel of Juniper Networks Junos OS allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). In an MPLS scenario specific packets destined to an Integrated Routing and Bridging (irb) interface of the device will cause a buffer (mbuf) to leak. Continued receipt of these specific packets will eventually cause a loss of connectivity to and from the device, and requires a reboot to recover. These mbufs can be monitored by using the CLI command 'show system buffers': user@host> show system buffers 783/1497/2280 mbufs in use (current/cache/total) user@host> show system buffers 793/1487/2280 mbufs in use (current/cache/total) <<<<<< mbuf usage increased This issue affects Juniper Networks Junos OS: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S9; 20.1 version 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R2.

A Missing Release of Memory after Effective Lifetime vulnerability in the kernel of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent, unauthenticated attacker to cause a Denial of Service (DoS). In a segment-routing scenario with OSPF as IGP, when a peer interface continuously flaps, next-hop churn will happen and a continuous increase in Routing Protocol Daemon (rpd) memory consumption will be observed. This will eventually lead to an rpd crash and restart when the memory is full. The memory consumption can be monitored using the CLI command "show task memory detail" as shown in the following example: user@host> show task memory detail | match "RTNEXTHOPSTEMPLATE|RTTEMPLATEBOOKKEE" RTNEXTHOPSTEMPLATE 1008 1024 T 50 51200 50 51200 RTNEXTHOPSTEMPLATE 688 768 T 50 38400 50 38400 RTNEXTHOPSTEMPLATE 368 384 T 412330 158334720 412330 158334720 RTTEMPLATEBOOKKEE 2064 2560 T 33315 85286400 33315 85286400 user@host> show task memory detail | match "RTNEXTHOPSTEMPLATE|RTTEMPLATEBOOKKEE" RTNEXTHOPSTEMPLATE 1008 1024 T 50 51200 50 51200 RTNEXTHOPSTEMPLATE 688 768 T 50 38400 50 38400 RTNEXTHOPSTEMPLATE 368 384 T 419005 160897920 419005 160897920 <=== RTTEMPLATEBOOKKEE 2064 2560 T 39975 102336000 39975 10233600 <=== This issue affects: Juniper Networks Junos OS All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S8, 19.4R3-S9; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R3-S4-EVO; 21.4 versions prior to 21.4R2-S1-EVO, 21.4R3-EVO; 22.1 versions prior to 22.1R2-EVO.

An Improper Control of a Resource Through its Lifetime vulnerability in Packet Forwarding Engine (PFE) of Juniper Networks Junos OS and Junos OS Evolved allows unauthenticated adjacent attacker to cause a Denial of Service (DoS). In an EVPN-MPLS scenario, if MAC is learned locally on an access interface but later a request to delete is received indicating that the MAC was learnt remotely, this can lead to memory corruption which can result in line card crash and reload. This issue affects: Juniper Networks Junos OS All versions 17.3R1 and later versions prior to 19.2R3-S5; 19.3 versions prior to 19.3R3-S5; 19.4 versions prior to 19.4R2-S6, 19.4R3-S8; 20.1 version 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S4; 20.3 versions prior to 20.3R3-S3; 20.4 versions prior to 20.4R3-S3; 21.1 versions prior to 21.1R3-S1; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2; 21.4 versions prior to 21.4R1-S1, 21.4R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R3-S3-EVO; 21.1-EVO version 21.1R1-EVO and later versions; 21.2-EVO versions prior to 21.2R3-EVO; 21.3-EVO versions prior to 21.3R2-EVO; 21.4-EVO versions prior to 21.4R1-S1-EVO, 21.4R2-EVO. This issue does not affect Juniper Networks Junos OS versions prior to 17.3R1.

An Improper Control of a Resource Through its Lifetime vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS on MX Series allows an unauthenticated adjacent attacker to cause a Denial of Service (DoS). When there is a continuous mac move a memory corruption causes one or more FPCs to crash and reboot. These MAC moves can be between two local interfaces or between core/EVPN and local interface. The below error logs can be seen in PFE syslog when this issue happens: xsseventhandler(1071): EA[0:0]PPE 46.xss[0] ADDR Error. ppeerrorinterrupt(4298): EA[0:0]PPE 46 Errors sync xtxn error xsseventhandler(1071): EA[0:0]PPE 1.xss[0] ADDR Error. ppeerrorinterrupt(4298): EA[0:0]PPE 1 Errors sync xtxn error xsseventhandler(1071): EA[0:0]PPE 2.xss[0] ADDR Error. This issue affects Juniper Networks Junos OS on MX Series: All versions prior to 15.1R7-S13; 19.1 versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R2-S7, 19.4R3-S8; 20.1 version 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S2; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2.

A PHP Local File Inclusion (LFI) vulnerability in the J-Web component of Juniper Networks Junos OS may allow a low-privileged authenticated attacker to execute an untrusted PHP file. By chaining this vulnerability with other unspecified vulnerabilities, and by circumventing existing attack requirements, successful exploitation could lead to a complete system compromise. This issue affects Juniper Networks Junos OS: all versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R2-S7, 19.4R3-S8; 20.1 versions prior to 20.1R3-S5; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R2-S2, 21.3R3; 21.4 versions prior to 21.4R1-S2, 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R1-S1, 22.1R2.

A Path Traversal vulnerability in the J-Web component of Juniper Networks Junos OS allows an authenticated attacker to upload arbitrary files to the device by bypassing validation checks built into Junos OS. The attacker should not be able to execute the file due to validation checks built into Junos OS. Successful exploitation of this vulnerability could lead to loss of filesystem integrity. This issue affects Juniper Networks Junos OS: all versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S9; 20.1 versions prior to 20.1R3-S5; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R2-S2, 21.3R3; 21.4 versions prior to 21.4R1-S2, 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R1-S1, 22.1R2.

An XPath Injection vulnerability in the J-Web component of Juniper Networks Junos OS allows an unauthenticated attacker sending a crafted POST to reach the XPath channel, which may allow chaining to other unspecified vulnerabilities, leading to a partial loss of confidentiality. This issue affects Juniper Networks Junos OS: all versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S9; 20.1 versions prior to 20.1R3-S5; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R1-S2, 21.4R2; 22.1 versions prior to 22.1R1-S1, 22.1R2.

An XPath Injection vulnerability due to Improper Input Validation in the J-Web component of Juniper Networks Junos OS allows an authenticated attacker to add an XPath command to the XPath stream, which may allow chaining to other unspecified vulnerabilities, leading to a partial loss of confidentiality. This issue affects Juniper Networks Junos OS: all versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S7, 19.4R3-S8; 20.1 versions prior to 20.1R3-S5; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R2-S2, 21.3R3; 21.4 versions prior to 21.4R1-S2, 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R1-S1, 22.1R2.

A Cross-site Scripting (XSS) vulnerability in the J-Web component of Juniper Networks Junos OS allows an unauthenticated attacker to run malicious scripts reflected off of J-Web to the victim's browser in the context of their session within J-Web. This issue affects Juniper Networks Junos OS all versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S7, 19.4R3-S8; 20.1 versions prior to 20.1R3-S5; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3; 21.4 versions prior to 21.4R2; 22.1 versions prior to 22.1R2.

An Improper Input Validation vulnerability in the J-Web component of Juniper Networks Junos OS may allow an unauthenticated attacker to access data without proper authorization. Utilizing a crafted POST request, deserialization may occur which could lead to unauthorized local file access or the ability to execute arbitrary commands. This issue affects Juniper Networks Junos OS: all versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S7, 19.4R3-S9; 20.1 versions prior to 20.1R3-S5; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R2-S2, 21.3R3; 21.4 versions prior to 21.4R1-S2, 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R1-S1, 22.1R2.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS). When an incoming RESV message corresponding to a protected LSP is malformed it causes an incorrect internal state resulting in an rpd core. This issue affects: Juniper Networks Junos OS All versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R3-S8; 20.1 versions prior to 20.1R3-S2; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S1; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R1-S2, 21.2R3; 21.3 versions prior to 21.3R2. Juniper Networks Junos OS Evolved All versions prior to 20.2R3-S3-EVO; 20.3-EVO version 20.3R1-EVO and later versions; 20.4-EVO versions prior to 20.4R3-S1-EVO; 21.1-EVO version 21.1R1-EVO and later versions; 21.2-EVO version 21.2R1-EVO and later versions; 21.3-EVO versions prior to 21.3R2-EVO.

An Improper Preservation of Consistency Between Independent Representations of Shared State vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows a locally authenticated attacker with low privileges to cause a Denial of Service (DoS). If the device is very busy for example while executing a series of show commands on the CLI one or more SFPs might not be detected anymore. The system then changes its state to "unplugged" which is leading to traffic impact and at least a partial DoS. Once the system is less busy the port states return to their actual value. Indicators of compromise are log messages about unplugged SFPs and corresponding syspld messages without any physical or environmental cause. These can be checked by issuing the following commands: user@device# show log messages | match unplugged %PFE-6: fpc0 sfp-0/1/2 SFP unplugged %PFE-6: fpc0 sfp-0/1/3 SFP unplugged The following log messages will also be seen when this issue happens: fpc0 Error tvpdrvsyspldread: syspld read failed for address <address> fpc0 Error[-1]:tvpopticspresenceget - Syspld read failed for port <pic/port> fpc0 optics pres failed(-1) for pic <pic> port <port> fpc0 tvpdrvsyspldread: i2c access retry count 200 This issue affects Juniper Networks Junos OS on EX2300 Series, EX3400 Series: All versions prior to 18.4R3-S11; 19.1 versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R1-S9, 19.2R3-S5; 19.3 versions prior to 19.3R3-S6; 19.4 versions prior to 19.4R2-S7, 19.4R3-S8; 20.1 versions prior to 20.1R3-S4; 20.2 versions prior to 20.2R3-S4; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S3; 21.1 versions prior to 21.1R3-S1; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2; 21.4 versions prior to 21.4R2.

An Improper Input Validation vulnerability in the Routing Protocol Daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent unauthenticated attacker to cause DoS (Denial of Service). If another router generates more than one specific valid OSPFv3 LSA then rpd will crash while processing these LSAs. This issue only affects systems configured with OSPFv3, while OSPFv2 is not affected. This issue affects: Juniper Networks Junos OS 19.2 versions prior to 19.2R3-S6; 19.3 version 19.3R2 and later versions; 19.4 versions prior to 19.4R2-S8, 19.4R3-S9; 20.1 version 20.1R1 and later versions; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R3-S2; 21.4 versions prior to 21.4R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R3-S5-EVO; 21.1-EVO versions prior to 21.1R3-S2-EVO; 21.2-EVO versions prior to 21.2R3-S1-EVO; 21.3-EVO versions prior to 21.3R3-S2-EVO; 21.4-EVO versions prior to 21.4R2-EVO; 22.1-EVO versions prior to 22.1R2-EVO; 22.2-EVO versions prior to 22.2R2-EVO. This issue does not affect Juniper Networks Junos OS 19.2 versions prior to 19.2R2.

In VxLAN scenarios on EX4300-MP, EX4600, QFX5000 Series devices an Uncontrolled Memory Allocation vulnerability in the Packet Forwarding Engine (PFE) of Juniper Networks Junos OS allows an unauthenticated adjacently located attacker sending specific packets to cause a Denial of Service (DoS) condition by crashing one or more PFE's when they are received and processed by the device. Upon automatic restart of the PFE, continued processing of these packets will cause the memory leak to reappear. Depending on the volume of packets received the attacker may be able to create a sustained Denial of Service (DoS) condition. This issue affects: Juniper Networks Junos OS on EX4300-MP, EX4600, QFX5000 Series: 17.1 version 17.1R1 and later versions prior to 17.3R3-S12; 17.4 versions prior to 17.4R2-S13, 17.4R3-S5; 18.1 versions prior to 18.1R3-S13; 18.2 versions prior to 18.2R3-S8; 18.3 versions prior to 18.3R3-S5; 18.4 versions prior to 18.4R1-S8, 18.4R2-S6, 18.4R3-S6; 19.1 versions prior to 19.1R3-S4; 19.2 versions prior to 19.2R1-S7, 19.2R3-S1; 19.3 versions prior to 19.3R2-S6, 19.3R3-S1; 19.4 versions prior to 19.4R1-S4, 19.4R2-S4, 19.4R3-S1; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2-S3, 20.2R3; 20.3 versions prior to 20.3R2. This issue does not affect Junos OS versions prior to 17.1R1.

An Improper Check or Handling of Exceptional Conditions vulnerability in the processing of a malformed OSPF TLV in Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated adjacent attacker to cause the periodic packet management daemon (PPMD) process to go into an infinite loop, which in turn can cause protocols and functions reliant on PPMD such as OSPF neighbor reachability to be impacted, resulting in a sustained Denial of Service (DoS) condition. The DoS condition persists until the PPMD process is manually restarted. This issue affects: Juniper Networks Junos OS: All versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S5; 19.3 versions prior to 19.3R3-S3; 19.4 versions prior to 19.4R3-S9; 20.1 versions prior to 20.1R3; 20.2 versions prior to 20.2R3-S1; 20.3 versions prior to 20.3R3; 20.4 versions prior to 20.4R3; 21.1 versions prior to 21.1R2. Juniper Networks Junos OS Evolved: All versions prior to 20.4R3-S3-EVO; 21.1 versions prior to 21.1R2-EVO.

On QFX10000 Series devices using Juniper Networks Junos OS when configured as transit IP/MPLS penultimate hop popping (PHP) nodes with link aggregation group (LAG) interfaces, an Improper Validation of Specified Index, Position, or Offset in Input weakness allows an attacker sending certain IP packets to cause multiple interfaces in the LAG to detach causing a Denial of Service (DoS) condition. Continued receipt and processing of these packets will sustain the Denial of Service. This issue affects IPv4 and IPv6 packets. Packets of either type can cause and sustain the DoS event. These packets can be destined to the device or be transit packets. On devices such as the QFX10008 with line cards, line cards can be restarted to restore service. On devices such as the QFX10002 you can restart the PFE service, or reboot device to restore service. This issue affects: Juniper Networks Junos OS on QFX10000 Series: All versions prior to 15.1R7-S11; 18.4 versions prior to 18.4R2-S10, 18.4R3-S10; 19.1 versions prior to 19.1R3-S8; 19.2 versions prior to 19.2R3-S4; 19.3 versions prior to 19.3R3-S5; 19.4 versions prior to 19.4R2-S6, 19.4R3-S7; 20.1 versions prior to 20.1R3-S3; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3; 21.2 versions prior to 21.2R3-S3; 21.3 versions prior to 21.3R3-S1. An indicator of compromise may be seen by issuing the command: request pfe execute target fpc0 command "show jspec pechip[3] registers ps l2node 10" timeout 0 | refresh 1 | no-more and reviewing for backpressured output; for example: GOT: 0x220702a8 pe.ps.l2node[10].pktcnt 00000076 GOT: 0x220702b4 pe.ps.l2node[10].backpressured 00000002 <<<< STICKS HERE and requesting detail on the pepic wanio: request pfe execute target fpc0 command "show pepic 0 wanio-info" timeout 0 | no-more | match xe-0/0/0:2 GOT: 3 xe-0/0/0:2 10 6 3 0 1 10 189 10 0x6321b088 <<< LOOK HERE as well as looking for tail drops looking at the interface queue, for example: show interfaces queue xe-0/0/0:2 resulting in: Transmitted: Total-dropped packets: 1094137 0 pps << LOOK HERE

On SRX Series devices, an Improper Check for Unusual or Exceptional Conditions when using Certificate Management Protocol Version 2 (CMPv2) auto re-enrollment, allows a network-based, unauthenticated attacker to cause a Denial of Service (DoS) by crashing the pkid process. The pkid process cannot handle an unexpected response from the Certificate Authority (CA) server, leading to crash. A restart is required to restore services. This issue affects: Juniper Networks Junos OS on SRX Series: All versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S4; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S1; 21.2 versions prior to 21.2R3; 21.3 versions prior to 21.3R2; 21.4 versions prior to 21.4R2.